Low water pressure in Lisbon: why it happens and what to do
Free tool: Water pressure check: why is it low?
Low water pressure is one of the most common complaints we hear from people living in Lisbon flats, especially in older buildings. The shower comes out as a trickle, the washing machine takes ages to fill, or someone opens the kitchen tap and the shower nearly stops. In most cases the cause is easy to pin down once you know where the pressure is weak: at one tap, only on the hot side, across the whole flat or across the whole building.
First, narrow it down
Do this quick test before anything else:
- Run the cold tap in several places (kitchen, basin, shower), one at a time.
- Do the same with the hot water.
- Ask a neighbour, ideally upstairs, whether their pressure is weak too.
Those three answers tell you which of the groups below you are in.
The usual causes, most common first
One tap or the shower only
Almost always limescale. Lisbon’s water is hard, and scale builds up in the aerator (the small mesh at the tip of the tap) and in the holes of the shower head. It can also be the filter in the small isolation valve under the basin, or a kinked flexible hose.
Only the hot water
If cold is fine and hot is weak, look at whatever heats the water, or at the mixer:
- Esquentador (gas tankless heater): blocked water inlet filter, scale in the heat exchanger, or a worn diaphragm in the water valve. Often the heater also starts cutting out or failing to light; see our guide on a water heater not working.
- Termoacumulador (electric storage tank): scale at the inlet, debris in the safety valve, or an isolation valve next to the tank left half closed.
- Thermostatic mixer: a dirty cartridge or inlet filter on the hot side.
A very common pattern: pressure dropped right after the heater was repaired or replaced. Usually an isolation valve was not fully reopened, a filter caught debris from the work, or a flexible hose got bent.
The whole flat
The likely causes here are:
- The main stopcock is not fully open. It happens after building work or a water cut.
- Old galvanised iron pipes. In the Pombaline and gaioleiro buildings in the centre, and in many 1960s to 1980s blocks in the suburbs, galvanised pipes rust on the inside and the bore gets narrower every year. Water may come out brownish when you first open a tap.
- A faulty pressure reducing valve, if your installation has one.
- A hidden leak after the meter, taking flow away. If the meter keeps turning with every tap closed, read our guide on a water meter that keeps running.
The whole building
If neighbours have the same problem, the cause is before your flat: in the prumada (the shared riser), in the building’s booster pump set if it has one, or in the public network. Top floors in buildings without a booster pump naturally get lower pressure. As a rule, shared parts are the condomínio’s matter and the network before the meter belongs to the water utility (EPAL in Lisbon, SIMAS in Oeiras and Amadora, SMAS in Sintra, Águas de Cascais, SIMAR in Loures and Odivelas, SMAS Almada, Câmara Municipal do Seixal). Talk to the administração (the company or person managing the building) first.
What you can check yourself
- Clean the aerators: unscrew the tip of the tap, take out the mesh and soak it in vinegar. Do the same with the shower head.
- Make sure the main stopcock is fully open, along with the small valves under basins and the isolation valves next to the water heater. If you are not sure where your stopcock is, see where to turn off the water in a Portuguese flat.
- Look at the meter with every tap closed. If it keeps turning, there is a leak.
- Notice the colour of the water first thing in the morning. Brown water points to rusting iron pipes.
- Compare hot and cold in each room and note what you find.
What not to do
- Do not take the esquentador apart. The gas side is not a DIY job.
- Do not buy a pump before you know the cause. It will not fix scale, clogged pipes or a leak.
- Do not force an old, stiff stopcock. It can snap and leave you with a much bigger problem.
- Do not pour harsh chemicals into mixers or thermostatic cartridges.
When to call a plumber, and what to send us
Call a plumber if the pressure is still weak after cleaning the aerators and checking the valves, if only the hot water is affected, if the water comes out rusty, or if you suspect a leak. On WhatsApp, send us:
- a short video of a tap running cold, and one running hot;
- a photo of the brand plate on your esquentador or termoacumulador;
- a photo of the water meter with every tap closed;
- your address and whether your neighbours have the same problem.
We reply fast with a written quote on WhatsApp before any work starts; nothing starts without your approval.
How it usually gets fixed
It depends on the cause. Scaled mixers and shower heads are cleaned or the worn part replaced. On an esquentador we clean the inlet filter and descale or replace the worn part. On a termoacumulador we service the tank and check the safety valve and connections. When galvanised pipes are clogged, the lasting fix is replacing the affected runs with multilayer or PPR pipe, often starting at the entry to the flat and the kitchen and bathroom. Tiling, plaster and painting are a builder’s job; we do the plumbing part. If the same fault comes back, we come back at no cost.
If low pressure is making daily life awkward, have a look at our emergency plumber service or send us the videos on WhatsApp. The team speaks English and Portuguese, you get a VAT invoice with your NIF (tax number), and we are rated 4.9 on Google with 1,000+ expats served.