Water pressure check: why is it low?
A weak shower, a tap that dribbles, hot water that barely runs? Answer five questions with the Water pressure check and see the likely cause, what to check yourself and when to call us. The bucket test underneath turns ten seconds at a tap into litres a minute.
Why is the water pressure low?
Question 1 of 5
Where is the pressure low?
Run the cold water in the kitchen, the basin and the shower, one at a time.
Is it only the hot water, or hot and cold?
Do the neighbours have low pressure too?
Ideally ask a neighbour upstairs.
Did it drop suddenly or bit by bit?
What colour is the water?
Look in a glass, in the morning, as soon as you open the tap.
Most likely cause
This is a guide, not a diagnosis: two causes can add up.
Bucket test (optional)
Hold a bucket or a jug with litre marks under the tap, open the cold water fully and count 10 seconds. Type in how many litres you collected.
The bucket measures flow, which is what you feel at the tap; pressure is measured with a gauge. Water-saving aerators and shower heads lower the flow on purpose.
First, narrow it down
Three answers tell you most of what you need to know. Run the cold water in the kitchen, the basin and the shower, one at a time. Do the same with the hot. Then ask a neighbour, ideally upstairs, whether their pressure is weak too. One tap or the whole home, hot only or hot and cold, your home or the whole building: the tool asks exactly those questions, and then when it started and what colour the water is.
The usual causes
- One tap or the shower only: almost always limescale in the aerator or the shower head. Lisbon's water is hard. It can also be the small isolation valve under the basin or a kinked flexible hose.
- Only the hot water: the esquentador (inlet filter, scale), the termoacumulador (scale at the inlet, the safety valve, a half-closed valve next to it) or the mixer tap's cartridge.
- The whole home, suddenly: a stopcock left partly closed after building work or a water cut, a faulty pressure reducing valve, or a leak taking water away.
- The whole home, bit by bit: old galvanised iron pipes rusting on the inside, common in Pombaline and gaioleiro buildings and in 1960s to 1980s blocks. The water may come out brownish first thing in the morning.
- The whole building: the water company's supply or the building's shared parts, such as the prumada or a booster pump. Top floors in buildings without a pump naturally get lower pressure.
The bucket test, in plain words
Hold a bucket or a jug with litre marks under the tap, open the cold water fully and count ten seconds. Multiply the litres by six and you have litres a minute. As a rough guide, under 4 litres a minute is low for a tap and under 6 is low for a shower. Water-saving aerators and shower heads lower the flow on purpose, so try it with the aerator off too: if the flow jumps, the aerator was the problem. The bucket measures flow, which is what you feel; pressure itself is measured with a gauge.
What not to do
Do not take an esquentador apart: the gas side is not a DIY job. Do not force an old, stiff stopcock, which can snap. Do not buy a pump before you know the cause: it will not fix scale, clogged pipes or a leak.
When to call us
Call us if the pressure is still low after cleaning the aerators and opening the valves, if only the hot water is affected, if the water comes out rusty, or if you suspect a leak. Finding a hidden leak is a paid visit, and our water meter test tells you first whether there is one. Our guide on low water pressure goes into more detail. Send us a short video of a tap running cold and one running hot on WhatsApp. You get a written quote on WhatsApp, and no work starts until you approve it.
Related service: Emergency plumber
Water pressure check: why is it low?
Why is the water pressure low in only one tap?
Almost always limescale in the aerator, the small mesh at the tip of the tap, or in the shower head. Unscrew it and soak it in vinegar. It can also be the small isolation valve under the basin left partly closed, or a kinked flexible hose.
Why is only the hot water pressure low?
If the cold is fine everywhere and the hot is weak, look at whatever heats the water: the inlet filter or scale in an esquentador, scale or a half-closed valve at a termoacumulador, or the cartridge of a mixer tap. It often starts right after the heater was repaired or replaced, when a valve was not fully reopened.
What is a normal water flow for a shower or tap?
As a rough guide, a water-saving shower head gives about 6 to 9 litres a minute and a tap with a water-saving aerator about 4 to 6. To measure yours, fill a bucket for 10 seconds and multiply the litres by six.
The neighbours have low pressure too. Who deals with it?
The cause is before your home: in the water company's network or in the building's shared parts, such as the prumada or a booster pump. As a rule, check the water company's notices and talk to the administração do condomínio first.
Can low pressure mean a leak?
Yes, a hidden leak after the meter takes water away. With every tap closed, watch the water meter: if it moves, there is a leak. Finding where it is is a paid visit, with the cost given on WhatsApp before you book.
Talk to a plumber
4.9 on Google. We fix it properly or we come back for free.
Leave your number, we WhatsApp you in under a minute.
WhatsApp and phone
Message us on WhatsApp at +351 21 700 9237 or call +351 21 700 9773.
4.9 on Google
Read what our customers say in our Google reviews.
English-speaking
1,000+ expats served across the Lisbon area.