Boiler not starting or showing an error code: safe checks and next steps
In most Lisbon area homes with central heating, a wall hung boiler (caldeira) does two jobs: it heats the radiators and, if it is a combi, the water at your taps too. So when it stops, you lose the heating and sometimes the shower as well. The display shows a code, a flashing light, or nothing at all. Before calling, a few simple checks solve some cases and help us understand the rest.
If you smell gas
Close the gas valve, open the windows, do not touch light switches, do not use lighters or matches, and leave the home. Call 112 or your gas supplier’s emergency line. The boiler can wait.
Four checks without opening the boiler
1. Is there power?
If the display is blank, check the fuse box and the plug or switch next to the boiler. After a thunderstorm or a power cut, some boilers lock out until the reset button is pressed.
2. Is there gas?
Try the hob, if it is gas. If that will not light either, the problem is the gas supply, not the boiler. With bottled gas, check whether the bottle has run out. Also check that the gas valve next to the boiler is in the open position, in line with the pipe. If you find it closed and do not know why, for instance after building work or an inspection, do not open it: speak first to whoever closed it or to your gas supplier. No gas anywhere in the home is a matter for the gas supplier or a certified gas company.
3. What is the pressure?
Look at the pressure gauge or the display. With the boiler cold, it should sit between 1 and 1.5 bar. Below 1 bar, many boilers lock out for safety. Our guide on a boiler losing pressure explains how to top up safely and what it means when the pressure keeps dropping.
4. Is anything calling for heat?
A room thermostat with flat batteries, a programmer that lost its time after a power cut, or a boiler left in summer mode (hot water only) can all look like a breakdown. Check the mode, turn the requested temperature up and wait a few minutes.
The code on the display
Every brand has its own list. The same code can mean no flame on one boiler and a temperature sensor on another, so looking up a code on its own online and acting on it is not much help. Broadly, errors fall into these groups:
- Pressure: the boiler senses too little water in the circuit.
- Flame or ignition: it tried to light and did not detect a flame. Gas supply, electrode or control board.
- Overheating or circulation: water is not moving properly, from air in the system, a stuck pump or a dirty filter.
- Sensors and board: a temperature probe or the electronics.
- Flue: a problem with the exhaust gases. In that case, do not switch it back on.
You can press reset once. If the same error comes back, stop and photograph the display.
What not to do
- Do not take the casing off or touch any gas or electrical parts.
- Do not reset over and over. On flame errors, each attempt lets gas through unburnt.
- Do not block air vents or the flue outlet, even if they let in cold air.
- Do not run a boiler with smoke, a burning smell or soot around the flue.
What to send us on WhatsApp
- a close photo of the display with the code and any light showing;
- a photo of the boiler’s rating plate, with brand and model;
- a photo of the pressure gauge;
- whether your gas hob works, and whether the boiler makes any noise as it tries to start;
- roughly how old the boiler is, your address and floor.
We reply with a written quote on WhatsApp before any work starts; nothing starts without your approval.
Repair or replace?
We repair Vulcano, Bosch, Junkers, Baxi and Vaillant boilers: electrodes, sensors, pumps, valves, expansion vessels and heat exchanger cleaning. For other brands, we offer a replacement with a new unit in the same place, on the existing connections. On an old boiler with repeated faults, we tell you honestly whether the part is still worth it.
How it usually gets fixed
On the visit we read the fault history, check pressure, circulation and ignition, and find the part involved. Many faults are fixed on the first visit with the right part. When the cause is air in the system or a dirty filter, we bleed and clean it. If a part has to be ordered, we tell you first and leave the boiler safe.
If your boiler will not start, have a look at our water heaters and boilers service or send us a photo of the display on WhatsApp. The team speaks English and Portuguese, you get a VAT invoice with your NIF (tax number), and we are rated 4.9 on Google with 1,000+ expats served.